Yutaka Nakai　YutaAtelier　120314 HOe Narrow gauge SAKURA Rail way Small Layout

I make a layout base with HINOKI wood squared lumber and SINA wood plywood.
(because I have begun to record it since a bass is done,
there is not the processing photograph of the base)

How to make makes the vehicle like a building. The specifications power uses a product made in KATO A headlight, tail lamp, the indoor light incorporate tip LED A driver, two passenger rides As for the head mark of "the flower viewing", disassembly is possible

It is the last finish. I express a wave in gel medium of the soft type. I describe the wave of the river in a right angle for a flow. (by the way, the sea does it parallel to a bank)

The second water is resin which colored Green. I pour it and stiffen this for 後 24 hours. The depth of the color is made by repeating two colors

I make the spray in same gel medium.

I pile gel mediumof the EX type to the glasswork and tear off by hardening, one of them and attach it to the sewage pipe

I bond a pebble to both sides of the river and finish it with the coloration of the bottom of a river

One of the wall surface is completion in this

In the building side of 0.3mm pierce it, and place it, and is crowded, and adhere in superglue

I let I pour each dry part and compete with adhesive

I clip out the part which does not completely fall out here and there with a medical female

I mask it in a makeup part of the base to produce a diorama.
Because the power pack operates every process and must confirm it
I mask it in the shape of a cover.

It is hard to look with the photograph,
but draws track placement and the positions such as buildings.

12031 SAKURA Rail way Small Layout(Japanese name NOBI HANAMI Rail way)

The third resin is transparent. Depth of the water comes out this time by pouring this (this is because range of resin thickens). ・ which rigidifies this for 24 hours

I design structure for dioramas by CAD while watching goods dimensions (the main body of layout)

Introduction of a work process

The cherry blossoms glue by little that is aSILFLOR together with tweezers

Work No.120314 NOBI HANAMI Rail way

The material of the grass is a SILFLOR,, too. By one stock adheres and does it

I fix the building at this stage
Because I do not yet attach it,
the inside is seen on the roof well

I paint it with color varnish (mahogany).
I paint four times and repeat it until finish.

I open a lead for illumination in each place.

I paint a track in the state that got rusty.

I fix electric wiring.

I make a trial and am a check and
the confirmation of the run.

The people finish it with paper for the painting smoothly.

I prepare a part of the spray in gel medium of the extra heavy type and stick it on a dropping part of the drainage

It is the first water container. I wait until the first pours colored resin into blue (I perform it four times) and stiffens for 24 hours

It is the preparations for cherry tree. Because I seem to be able to just use the bark for a cherry tree, I use this this time. (the thing which I dried after the choice for half a year, and stored the dead twig of the rosemary which I brought up in a garden)

I set up wire and paint it in rust
The broken stakes keep a change made

I solder a lead to LED of the illumination in the building

I bury a stake along the track

I apply the plasters which I mixed material of a plaster and the soil with on the important points

If ballast dries, I mask it in a track

I fix deck garters and a supporting beam, a sewage pipe and get the topography fixed with a plaster

If the hope (it is thickness) of the fittings of a common residence is made into 1/87 30 mm, it will be set to about 0.35 mm and will serve as a result almost
near an absolute size.

Before constructing a building,
it finishes paint of a fittings portion.

Glass is pasted up inside each window portion.

Put it away through a railroad tie and
put it to the board and confirm it.

I put a railroad tie through the track.

I bend a rail according to the placement figure.

If the painting dries, I incorporate original power pack.
The power pack forgot to take a photograph in a production process

It is completion of the water in this

I harden powder with liquid adhesive

I color all parts it faintly

I sprinkle the powder which I mixed several colors of green with

I model the topography in a styrene board and stick cork.
I change the railroad tie of the iron bridge part.

I solder a feeder.

I complete a sash before completing a clapboard to
an outer wall

I sprinkle ballast.

I hang down liquid adhesive and harden ballast.

The photograph explains the process to completion.

Soil moiety of the ground I push the model in JIGU, and the piling-stones part comes

I finish a flower viewing visitor to employ under the wisteria trellis

The left photograph is a cake ( MANJU )
to put on the dish ()
To a teapot and a teacup, a beer bottle glasses
I fix an accessory to the folding stool

All the delicate parts of all structure reinforce it in this way